Feem ntau faults thiab txij nkawm ntawm labeling machinery

1. Misaligned daim ntawv lo lub thawv txoj hauj lwm

2. Cov kua nplaum tuab heev lossis kub tsis dhau

3. qias neeg los yog hnav daim ntawv lo lub nruas daim txhuam cev

4. Kev tso lub raj mis tsis raug (misaligned nkag lub hnub qub log)

1. Kho lub thawv ntawv rau qhov chaw zoo

2. Tswj cov kua nplaum thiab xyuas kom qhov kub thiab txias yog 26-28 degree

3. Ntxuav lossis hloov daim ntawv lo ntawm daim txhuam cev

4. Txheeb xyuas thiab kho lub log lub hnub qub nkag thiab lub khob nruab nrab

1. Tsis sib npaug hauv qab kab ntawm lub thawv ntawv

2. Unflat daim ntawv lo rau hauv lub thawv ntawv

3. Tsis sib luag daim txhuam cev thickness los yog hnav lub raj mis tuav roj hmab ncoo

1. Kho qhov theem ntawm lub thawv ntawv

2. Npaj daim ntawv lo thiab kho daim ntawv lo kom nws tiaj tus

3. Hloov daim txhuam cev tsis tu ncua thiab hnav cov roj hmab ncoo

1. nruj heev los yog tsis tsim nyog angled daim ntawv lo nuv

2. Cov kua nplaum nplaum dhau heev tsis huv tom qab kaw

3. Asynchronous daim ntawv lo clamp nkaus

1. Kho lub kaum sab xis thiab nruj ntawm daim ntawv lo nuv

2. Ntxuav lub raj mis kua nplaum ua ntej kaw thiab hloov nrog cov kua nplaum tsim nyog

3. Tshawb xyuas thiab kho cov synchronization ntawm daim ntawv lo clamp thiab cam txoj hauj lwm

1. Qhov loj me me yuam kev ntawm daim ntawv lo

2. Tshaj dhau nruj daim ntawv lo nuv lossis lub caij nplooj ntoos hlav xoob dhau

3. Tsis tsim nyog clamping qhov tob ntawm lub cim nruas (zoo tagnrho: 4-5mm)
4. Tsis sib haum ntawm daim ntawv cim thiab cov kua nplaum

1. Siv tus qauv tsim nyog - daim ntawv lo lo lo ntxhuav

2. Kho daim ntawv lo lo lo ntxhuav los yog hloov lub caij nplooj ntoos hlav

3. Kho qhov tob clamping ntawm lub cim nruas.
4. Hloov cov ntawv cim lossis kua nplaum tsim nyog.

1. Servo lub cev muaj zog / synchronous siv siv

2. Hnav thiab pa tawm ntawm coding tshuab lub tog raj kheej foob nplhaib

3. Servo motor davhlau ya nyob twg xoob tswb

1. Tsis tu ncua tshuaj xyuas thiab hloov cov khoom hnav

2. Hloov lub tog raj kheej foob nplhaib

3. Tighten tag nrho cov khoom siv hluav taws xob

1. Kev ua yuam kev ntawm daim ntawv lo dispensing sensor (ib yam khoom pom ob zaug)

2. Tilted los yog hnav kua nplaum phaj

3. Kev teeb tsa lub sij hawm xa ntawv tsis raug

1. Kho qhov rhiab heev thiab txoj hauj lwm ntawm lub sensor

2. Kho lossis hloov cov nplaum nplaum

3. Fine-Siv daim ntawv lo rau lub sijhawm ua haujlwm ntawm lub vijtsam ua haujlwm (nce lub sijhawm rau cov ntawv siab, txo lub sijhawm rau cov ntawv qis)

1. Tsis paub meej batch number printing (blurred label)

2. Lub raj cua sov puas

3. Cov pa tawm ntawm lub tog raj kheej luam ntawv lossis solenoid valve jamming

1. Tshawb xyuas thiab hloov lub raj cua sov

2. Ntxuav lossis hloov lub tog raj kheej thiab solenoid valve

3. Xyuas kom cov khoom siv ribbon ib txwm muaj thiab ua haujlwm raug sensor

1. Kev ntxuav: Tom qab kaw, ntxuav cov kua nplaum uas seem thiab cov ntawv pov tseg ntawm lub thawv ntawv, daim ntawv lo clamp, thiab daim ntawv nplaum daim txhuam cev.

2. Kev tshuaj xyuas: Xyuas seb qhov cua qhov siab yog qhov qub thiab yog tias cov sensors huv.

3. Kev lees paub: Paub meej tias cov kua nplaum viscosity tsim nyog thiab yog tias qhov seem ntawm cov ribbon txaus.

1. Tightening: Tshawb xyuas thiab ua kom nruj cov cuab yeej siv tshuab (xws li lub sijhawm siv, cov ntsia hlau) thiab cov khoom siv hluav taws xob.

2. Lubrication: Lubricate tsim nyog txhua yam txav chaw (xws li lub tog raj kheej qhia rods).

3. Kev Tshuaj Xyuas Hnav: Tshawb xyuas qhov hnav ntawm cov khoom tsis zoo xws li cov nplaum nplaum, daim txhuam cev, thiab lub raj mis ntim cov roj hmab.

1. Comprehensive Calibration: Systematically calibrate labeling positions, printing positions, thiab tag nrho cov sensors.

2. Hloov cov khoom tsis zoo: Npaj hloov cov ntsaws ruaj ruaj, siv sijhawm ntev, cov nplaum nplaum thiab lwm yam khoom raws li kev siv.